« previous next »
Pages: 1 2 [3]  All   Go Down

Author Topic: 1/48 An-2 Colt in Czech Markings  (Read 5338 times)

Offline Buzzbomb

  • Low Concentration Span, oft wanders betwixt projects
  • Accurate Scale representations of fictional stuff
    • Club and my stuff site
Re: 1/48 An-2 Colt in Czech Markings
« Reply #50 on: September 18, 2025, 06:53:27 AM »
The cargo gives me a chuckle.
Logged

Offline Old Wombat

  • "We'll see when I've finished whether I'm showing off or simply embarrassing myself."
  • "Define 'interesting'?"
Re: 1/48 An-2 Colt in Czech Markings
« Reply #51 on: September 18, 2025, 09:52:05 AM »
Thanks, BT! That was the aim, to raise a chuckle, or at least a smile.  :smiley:
Logged
"This is the Captain. We have a little problem with our engine sequence, so we may experience some slight turbulence and, ah, explode."

Offline Robomog

  • ...had a very bad experience with [an] orange...
  • Would you buy a used kit from this man?
Re: 1/48 An-2 Colt in Czech Markings
« Reply #52 on: September 21, 2025, 06:22:27 PM »
Oh it definitely raised a smile going on full grin  ;D ;D

Dreams of relocating stash maybe, or adding to it bigtime  ;)

Mog
>^-.-^<
Logged
Mostly Harmless...............

Offline Old Wombat

  • "We'll see when I've finished whether I'm showing off or simply embarrassing myself."
  • "Define 'interesting'?"
Re: 1/48 An-2 Colt in Czech Markings
« Reply #53 on: September 23, 2025, 03:13:53 PM »
New air-compressor has been set up & work has recommenced on the An-2 !  :smiley:
Logged
"This is the Captain. We have a little problem with our engine sequence, so we may experience some slight turbulence and, ah, explode."

Offline Claymore

  • It's all done with smoke and mirrors!
  • Alt Hist AFV guy with a thing for Bradley turrets
Re: 1/48 An-2 Colt in Czech Markings
« Reply #54 on: September 24, 2025, 12:46:59 AM »
Go to it my good man.  Spay like you have never spayed before!  ;D
Logged
Pass the razor saw, there is work to be done!

Offline Old Wombat

  • "We'll see when I've finished whether I'm showing off or simply embarrassing myself."
  • "Define 'interesting'?"
Re: 1/48 An-2 Colt in Czech Markings
« Reply #55 on: September 24, 2025, 01:37:47 AM »
Well, I've finished the last piece of cargo a "damaged" metal box for "Damaged" magazine ... It's barely visible behind a pile of other boxes, but it looked pretty good before I hid it away.  :D  ::)

And I've almost finished a scratch-built briefcase.
Logged
"This is the Captain. We have a little problem with our engine sequence, so we may experience some slight turbulence and, ah, explode."

Offline Old Wombat

  • "We'll see when I've finished whether I'm showing off or simply embarrassing myself."
  • "Define 'interesting'?"
Re: 1/48 An-2 Colt in Czech Markings
« Reply #56 on: September 24, 2025, 03:38:09 PM »
Fuselage glazing is in (I don't think I can fit the 2-piece cockpit glazing until after the fuselage is together, I've had a test run).

Just finishing off the pilot's briefcase.

Once that's done & in, & the masking's cut for the fuselage windows (just in case they pop out when I'm doing the masks), It'll be time to slap the fuselage halves together around the interior.
Logged
"This is the Captain. We have a little problem with our engine sequence, so we may experience some slight turbulence and, ah, explode."

Offline Old Wombat

  • "We'll see when I've finished whether I'm showing off or simply embarrassing myself."
  • "Define 'interesting'?"
Re: 1/48 An-2 Colt in Czech Markings
« Reply #57 on: Yesterday at 10:08:24 PM »
Finished cockpit:

Logged
"This is the Captain. We have a little problem with our engine sequence, so we may experience some slight turbulence and, ah, explode."

Offline Old Wombat

  • "We'll see when I've finished whether I'm showing off or simply embarrassing myself."
  • "Define 'interesting'?"
Re: 1/48 An-2 Colt in Czech Markings
« Reply #58 on: Yesterday at 10:20:56 PM »
Quite visible with the glazing in place;






The rather messed up corner of the glazing;

Logged
"This is the Captain. We have a little problem with our engine sequence, so we may experience some slight turbulence and, ah, explode."

Offline Dr. YoKai

  • Was in High School when mastadons roamed the plains...
  • A notorious curmudgeon who is partial to...hemp!
Re: 1/48 An-2 Colt in Czech Markings
« Reply #59 on: Yesterday at 10:35:29 PM »
The interior work continues to be amazing. I'm also filled with envy at how  visible it remains (And you can see the riveting on the framing!  :o)
Logged

Offline Old Wombat

  • "We'll see when I've finished whether I'm showing off or simply embarrassing myself."
  • "Define 'interesting'?"
Re: 1/48 An-2 Colt in Czech Markings
« Reply #60 on: Today at 12:02:34 AM »
Thanks, Doc!  :icon_alabanza:

It helps to be working in 1/48 & not afraid to use 1/35 accessories (as long as they don't look over-sized).  ;)

And the visibility is all thanks to the Antonov design bureau & the clarity of the Hobby Boss clear parts.  ;D
Logged
"This is the Captain. We have a little problem with our engine sequence, so we may experience some slight turbulence and, ah, explode."
Pages: 1 2 [3]  All   Go Up
« previous next »