Author Topic: Martin B-51G Panther “Tropic Moon III” Finished!!!  (Read 16529 times)

Offline trickyrich

  • The Resin Casanova
  • now if I just had time to finish all my projects!!
Martin B-51G Panther “Tropic Moon III” Finished!!!
« on: July 28, 2015, 09:06:36 PM »
Well the GB for this project is just about to start so I am starting this build thread properly. This build is part of a WhatIf GB on another site so I will be running a build on that site plus another one (I know some know me on all three sites). The build update will be exactly the same on all three sites, just the local replies to comments will be different.

I have been waiting for this build for quite sometime, 2 years to be exact, so it had to be something epic to celebrate it!! At one stage I was going to build the Arado Ar-234 P5 “Turbo-Prop” Nightfighter (which I am currently building here) for this build but after seeing some of the parts I didn’t think I would be able to complete it in the time available, as there was a lot of work required. My work patterns have changed so I do have more time for modelling now, and that build just seems to be just falling together. It’s too late for the GB as it’s past the 25% rule.

Then I as I mentioned in another thread I happened to see some amazing profiles by the artist Logan Hartke and I just fell in love with the ones of the B-51 Panther, which are based on the Martin XB-51. So after a couple of e-mails to him I had his blessing to use one of the photos as the basis for the build. Actually he was very excited to see someone actually try to bring this design to life (Very much appreciated Logan, I do hope I can do your wonderful profile justice!!).



So the base of the build will be Anigrands XB-51!  I had hoped to have had Collect-Aires 1/48th version (I will build one as soon as I can get one) as trust me it would have been an easier build than the Anigrand one….more on that later.





The new nose and canopy(?) will be from an Italeri B-57G along with a couple of other bits supplied from it as well. Though I have found a F-4E canopy that looks quite good on it as well!



Plus just to give myself a little bit more work a 1/72nd Master M61 Vulcan rotary cannon will be fitted to the weapons bay as per the Pave Gat program originally fitted to a couple B-57G’s in Vietnam in 1968. Insanely small PE….my favourite…I think not!

Finally she’ll be finished in RAAF colours for SEA operations around 1971. 

Work required;

•   Ok the Anigrand base model is horrible! All four sections of the fuselage were and still are warped, even a nice warm bath didn’t work, I think it made it worse! So lots of work there.

•   Main wheel well bays need to be rebuilt, are warped.
•   Completely new cockpit to be built.
•   Canopy will either be from the B-57 donor or a F-4E
•   Modernise the XB-51 airframe
•   Get carried away with any additional mods I always end up doing!!!

Well I have my work cut out for this one……but am so excited I can’t wait!!!

Oh the aircrafts full title is Martin B-51G Panther Tropic Moon III wt Pave Gat. The actual Tropic Moon III program started in 1967 as a result of operational requirements in Vietnam. Have managed to get the original de-classified documents for the program, which is really cool and very helpful!

So after much talk the build well begin this weekend…gee I’m a sucker for punishment!
« Last Edit: October 09, 2015, 03:03:55 PM by trickyrich »

Offline LemonJello

  • MARPAT Master
  • Member number 100...WooHoo!!!
Re: Martin B-51G Panther “Tropic Moon III” build!!!
« Reply #1 on: July 28, 2015, 10:05:30 PM »
I'll be following this build with great interest and anticipation! 

Offline Logan Hartke

  • High priest in the black arts of profiling...
  • Rivet-counting whiffer
Re: Martin B-51G Panther “Tropic Moon III” build!!!
« Reply #2 on: July 29, 2015, 12:05:36 AM »
Me, too! You're going to be the first person to actually bring one of my profiles into plastic as far as I know, so I can't wait to see this one!

Cheers,

Logan

Offline finsrin

  • The Dr Frankenstein of the modelling world...when not hiding from SBA
  • Finds part glues it on, finds part glues it on....
Re: Martin B-51G Panther “Tropic Moon III” build!!!
« Reply #3 on: July 29, 2015, 08:37:13 AM »
Me too.  Delighted to see this build.  Cool jet 8)
Have that kit and a vacuform B-51 in stash.  When find it will check fit.
1/72 B-51 really should be injection kit by now.

Logan - appreciate the inspiring profiles.
« Last Edit: July 29, 2015, 02:26:32 PM by finsrin »

Offline Dr. YoKai

  • Was in High School when mastadons roamed the plains...
  • A notorious curmudgeon who is partial to...hemp!
Re: Martin B-51G Panther “Tropic Moon III” build!!!
« Reply #4 on: July 29, 2015, 08:57:53 AM »
 Always glad to see someone building a XB-51. Sorry the kit is such a chore - hang in there.

Offline FAAMAN

  • 'bin building for years ....... and it feels it!
  • Always thought of himself as a 'straight' modeller
Re: Martin B-51G Panther “Tropic Moon III” build!!!
« Reply #5 on: July 29, 2015, 02:02:18 PM »
Can't wait to see this :), love the XB-51, on with the show  ;D
"Resistance is useless, prepare to be assembled!"

Offline trickyrich

  • The Resin Casanova
  • now if I just had time to finish all my projects!!
Re: Martin B-51G Panther “Tropic Moon III” build!!!
« Reply #6 on: July 29, 2015, 10:27:31 PM »
Thanks for all the nice comments, I have been looking forward to this build for sometime. The Arado build as difficult as it has been has given me  a lot of confidence for this one. It should be a lot simpler as the conversion is quite simple, the main issue is the warped fuselage. This shouldn't be too much of an issue as the resin is quite thick, so lots of rubbing down and filler will be the order of the day.

I do hope I can do justice to your profile Logan, that is probably one of the scariest things of the build!!! 

Offline trickyrich

  • The Resin Casanova
  • now if I just had time to finish all my projects!!
Re: Martin B-51G Panther “Tropic Moon III” build!!!
« Reply #7 on: August 02, 2015, 10:37:30 PM »
Ok time to start this build!

First off the rear fuselage was jointed together…oh that was fun too!! As can be seen the gaps are quite noticeable as well as the now warped wheel well! Unlike all the other resin models I have this one didn’t like the warm/hotish water bath at all, at first it did try to straighten the warped bits but as they cooled down they did crazy stuff!!! So there is a bit of work to do bit nothing like I have had to do on the Arado!!



The forward fuselage section is just as bad but this time one side is longer than the other!! The water bath didn’t do this!!



So with the two sections together you can see the fun I am going to have!! Nothing some filler and wet-n-dry won’t fix!



Now some of the updating work I will do, the tail section is quite plain, on the profile Logan has added a spike on the “T” junction, I’ll add something similar except it will be a little squarer in shape to house an antenna array.



There is something wrong with this picture!!! All three engines are meant to be GE J-47-GE-13’s so you’d expect them all to have intakes with the same opening areas! Clearly they didn’t get this one right! MY beast will have the later J-47-GE-27’s (as fitted to the F-86F’s, these had 5970lbs of thrust as opposed to the original 5200lbs ones of those fitted to the XB-51’s. So revised intakes are a must and the fuselage actually has a recessed section in it for the upper intake, so this one will have an enlarged intake and larger recessed section.



I have had a look at the three different options I have for the canopy, original, B-57G version, and one from a F-4E. While the B-57G one looks good from the side profile it’s quite wide when viewed from above and the fuselage is quite narrow. The F-4 one suits the era quite nicely so that’s the way I’ll be going, plus it will be much easier to profile it in!



Finally I had a look at some of the options I will have for stores. Due to it being a wee bit on the thirsty side, drop tanks are a must! Now being a Tropic Moon beast with the high-tech nose early LGB’s or Bullpup’s will be the go, and maybe AN/ALQ-87 or AN/ALQ-101 ECM pods.



Plus I have to build a new cockpit area and new main wheel wells!

While there appears to be quite a bit of work required it is all quite manageable. This should be a fun build and with luck I’ll dive right into it next weekend!

Offline trickyrich

  • The Resin Casanova
  • now if I just had time to finish all my projects!!
Re: Martin B-51G Panther “Tropic Moon III” Update 02/8
« Reply #8 on: August 05, 2015, 06:23:02 PM »
Well the fun has begun and I have a workbench covered in resin dust…it would have been so much easier if it had been a plastic model!

So we’ll start with the rear fuselage section first. Thought I have been asked why I didn’t first glue the front and rear sections first, then glue the halves together…good question! Probably because I like to make things difficult for myself! But really with the sections being quite warped and fuselages being different lengths doing it this way is the easiest. Plus she’s very long it would make life a bit harder as I’m bound to break something, along with the fact I’m rebuilding the wheel wells as well!

So with the rear section glued together and given a quick rub down off we go.

First up the wheel well, I’ll be doing both the same. So I make a basic box for the well with the side the right height, I’m not worried about the ends for the moment, just that they are longer then necessary (who could have guessed a simple box would be so hard to make!!!). Then using the model and reference photos I add some detail, it’s not quite exact but looks the part. Then fit….well there is a little bit more involved in this part, for the rear one I had to first grind out the old one so the new one will fit, quite a long process. The front section will be a bit different as because I’m fitting a new cockpit as well I’ll do all this work before I join the halves together.



It actually doesn’t look to bad at all, there are quite a few sins which are hidden but it does look so much better, plus it would have been a horrible job to fill those gaps! As it turns out the models wheel well are too short and the doors are even smaller…guess I’ll be custom making those as well!





Next up the intake for the #2 engine, as it turns out I missed something completely with this one! The #2 engine was only used for take offs, so it was fitted with a rotating cover/fairing. In its open position there should be a lower section of the intake visible. So an old drop tank was sacrificed for this job along with another one for the intake proper further in. Plus the upper part of the intake was removed and enlarged slightly. I now have an intake with roughly the same inlet area as the other two.  After some filler, sanding and profiling she should look great!



Next up the spike on the tail, it seems some aircraft didn’t had it (suspect early prototype/s) while later ones had different shaped ones. So I’ve made one up, it still needs some tiding up plus I’m probably going to add another fairing as well…hmm think about that one.



I have started the basic shaping of the canopy but won’t do too much more until the cockpit is done and the fuselage is together. Speaking of the cockpit I have decided to go with an aftermarket one for the B-57 (oh I’ve decided to use that one instead of the F-4’s one) as it will be simpler and look much better.

So just taped together…… I love the look of it!! She’s a big aircraft with a long body and not so big wings, by all reports she handled nicely and was fast, her only real problem was she was thirsty!





It’s turning out to be more than a simple conversion but that seems to be the case for any of my builds like this. I still think the Collect-Aire 1/48th version would have been a simpler build…I even have a Collect-Aire B-57G ready to donate its nose as well! Well at least I have until late November, when the GB finishes, to complete her!

Offline Logan Hartke

  • High priest in the black arts of profiling...
  • Rivet-counting whiffer
Re: Martin B-51G Panther “Tropic Moon III” Update 05/8
« Reply #9 on: August 05, 2015, 11:04:56 PM »
It's already looking great, Rich! I know that nose does nothing for the aesthetics, but it does look a lot more business-like. Well done!

In case anyone is wondering for any future projects, we used the B-66 Destroyer's engine pods for the J57 upgrade and the Caravelle's for the Avon upgrade.

Cheers,

Logan

Offline Talos

  • First candidate for the BTS Gulag...
  • It's riveting!
Re: Martin B-51G Panther “Tropic Moon III” Update 05/8
« Reply #10 on: August 08, 2015, 09:46:57 AM »
Looking great! This is the first model I can think of based on a profile drawing Logan and I've done. If you want lineart-accurate canopy, I used the F-101B canopy as a base for the drawing. The B-57's looks nice on it too.

EDIT: Didn't know this was mentioned by Logan on the other forum. Whoops.
« Last Edit: August 08, 2015, 09:59:14 AM by Talos »

Offline trickyrich

  • The Resin Casanova
  • now if I just had time to finish all my projects!!
Re: Martin B-51G Panther “Tropic Moon III” Update 05/8
« Reply #11 on: August 08, 2015, 11:50:55 AM »
thanks, it's nice to here yours and Logan's comments.

I did sort of wonder at first what canopy you'd used as the B-57's didn't quite fit or look the same. The F-101B's canopy probably would have made it a bit easier, but since when have I ever made builds like this easy for me!


Offline finsrin

  • The Dr Frankenstein of the modelling world...when not hiding from SBA
  • Finds part glues it on, finds part glues it on....
Re: Martin B-51G Panther “Tropic Moon III” Update 05/8
« Reply #12 on: August 08, 2015, 12:53:55 PM »
Very righteous of you to bring us a 60s-70s-? B-51G 8)
Is also example of extended service life.
Perhaps including service in first gulf war.

Offline trickyrich

  • The Resin Casanova
  • now if I just had time to finish all my projects!!
Re: Martin B-51G Panther “Tropic Moon III” Update 05/8
« Reply #13 on: August 11, 2015, 04:51:45 PM »
Well the replacement cockpit has finally arrived seeing the first one I ordered didn’t arrive….who knows where it will end up! So lot the fun continue.

As mentioned earlier I wanted the cockpit position sorted out before I closed up the front fuselage section. After couple of hours messing about I finally had it in a position I was happy about. This is not its final position but it’s close enough to allow me to close up the fuselage.



So after adding lots and lots of superglue gel and accelerator I ended up with gaps and joins like this….scary!!!



Not one to mess around they were given a very rudimentary going over with 240 grit wet & dry before being joined with the rear fuselage section. I wasn’t to concerned at the moment about how the front section looked as once it was align with the rear section the whole lot would be sanded to profile. The aligning required a couple of little plastic pegs/wedges to help, bit all was good. So more superglue and accelerator and a really good going over with wet & dry and I ended up with nice joins like this!



The fuselage does have a few dimples/ripples bit some filler will sort them out.

Next the radome/sensor head. The nose needed a bit of surgery for the radome to fit correctly….though I did get a bit carried away!



There is nothing behind the sensor window so I figured while I was here I’d at least add something, so it’s now all boxed up and I’ll add some sensors to it later. Plus I needed to add some “padding” around the sensor pod to help with the fit.



So again after superglue, accelerator and some filler the nose is on, and I’m happy to say it’s even aligned up properly!



So what’s all this work look like….

The tail is pretty well complete (she’s just sitting there for the photo), I’ll give it another quick undercoat to look for any final defects.



The #2 intake so pretty well complete as well, though a little more cleaning up is required. The patch of filler on the side was needed as that section had a very noticeable warp in it. So some plastic strip and filler to the rescue.




The forward wheel well will be fitted once the underside sanding is completed, I did run into a problem here as my new wheel well was slightly wider than the hole and there was very little material left in the fuselage. Some wafer thin sanding of the new wheel well was required….it’ll fit….just!



I was just playing around with some possible loadouts, though the drop tanks will be used.



She is a big sucker!!!



While I was waiting for the cockpit to arrive and in a fit of complete madness I decided to build up the Gatling gun! This is another one of those beautiful products for Master Models. As you can see she is tiny and is made up of 17 parts! Amazingly I didn’t loose any bits while building it and it didn’t take long to build. Pity though that this will be hidden from view under the aircraft!


Offline FAAMAN

  • 'bin building for years ....... and it feels it!
  • Always thought of himself as a 'straight' modeller
Re: Martin B-51G Panther “Tropic Moon III” Update 11/8
« Reply #14 on: August 11, 2015, 05:50:07 PM »
Coming along awesomely!!!  8) 8)
"Resistance is useless, prepare to be assembled!"