3D Printers

[GTX_Admin]

There is certainly a lot of talk of that - see here for example.

[Jeffry Fontaine]

One additional benefit of 3D printing is that you no longer need to create a different scale master for each item offered for sale.  A very good example of this was experienced this morning when I discovered a set of six Para-Pack racks for the C-47/Dakota that were only available in 1:72nd scale at Shapeways.  A quick note to the creator asking if they could be made available in 1:48th scale resulted in that actually happening within an hour of posting my query. 

Link to 1:72nd scale Parapacks (set of six) @Shapeways.com

Link to 1:48th scale Parapacks (set of six) @Shapeways.com

So for anyone that has a 1:48th scale Monogram C-47 kit (or the Trumpeter kit) that wishes to add a nice detail feature to the underside of the fuselage this is your chance to do so at a reasonable price. 


***Update:  I just ordered two sets of the 48th scale Para-Pack Racks in frosted ultra-high detail plastic @$30.00/ea.  Hoping to see them on my front door step before the end of the year :)

[Frank3k]

One additional benefit of 3D printing is that you no longer need to create a different scale master for each item offered for sale. 

In general, yes. If the original design has been made to minimize volume (and cost) rescaling may result in wall thickness (or details) that are either too thin to print or they will be printable but will deform or break with handling. The designer has to check the new design to make sure it's printable and buildable.

[Silver Fox]

Just found out that my local public library has a 3D Printer available to the general public... assuming you are a library member.

I'm going to have to scope out some of the parts I want and then see if I can get hooked up to print them out.

$1.00 setup and $0.05 per minute... nice. :)

[GTX_Admin]

As expected, these are becoming more and more prevalent (which will hopefully see great increases in usability, resolution as well as price reductions).  Here are just a couple shown at the recent 2015 Consumer Electronics Show in Las Vegas:

[Jeffry Fontaine]

A very well done article today at Cracked.com about using 3D printers to help people: 5 Ways to Help the Most People Possible With One 3D Printer. 


(Image source: Tim Freccia / Not Impossible - Project Daniel)

Image source link provides more information on Not Impossible - Project Daniel if you are interested in learning more about this project.

[Volkodav]

Literally just placed my first order at Shapways and I seriously want to buy my own 3D printer but I don't have a clue where to start or how to workout what to get.

[KiwiZac]

Just found out that my local public library has a 3D Printer available to the general public... assuming you are a library member.

That is absolutely brilliant.

For fun I went to a local retailer's website to check if their printer price had come down at all. No, but they now have four or five variations, "filament" cartridges in different colours for each brand, and scanners!! 3D scanners! The first one I saw was a handheld, the second a desktop turntable setup. Truly, the possibilities for modelling are endless! Got a rare kit? Scan it before you build it so you can print more! Perfect for my Aurora Cheyenne.

So. Damned. Cool. Of course I can't afford it but, like I assured Sam, I will wait until affordable models are affordable to me.

[arkon]

I know most if not all of these printers only print in one material at a time but I'm just wondering if they can print with two different materials, say one plastic and one that conducts electricity, so that you could print your model pre-wired for lights n motors or such.
Just a thought.

[Frank3k]

I know most if not all of these printers only print in one material at a time but I'm just wondering if they can print with two different materials, say one plastic and one that conducts electricity, so that you could print your model pre-wired for lights n motors or such.
Just a thought.

They're working on that, but I don't think there are any commercial products.

For modeling purposes, filament printers are going to leave steps that have to be sanded off or buried under thick paint.
Lazy people like me would rather have a resin printer. Just some minor cleanup and you're good to go.
Resin printers are still in the $2K and up range. There are a couple of Kickstaters for small "hobbyist" resin printers.

Here's a "cheap" one for $3300: http://formlabs.com/products/form-1-plus/

If you don't mind a tiny print area, here's one for $300: http://www.iboxprinters.com/

[arkon]

I'm not looking to buy one , was just wondering. I saw a picture of a car from this years Sema show where they had a car that was said to be completely 3d printed by a company called Local Motors I believe and was just wonder if that included circuits , so no more wire harness for the car which lead me to think in model applications.
Did not read the whole article on the printed car so I may be jumping to conclusions

[GTX_Admin]

One to possibly watch:

http://www.sprintray.com
https://www.kickstarter.com/projects/sprintray/moonray-worlds-best-desktop-3d-printer?ref=category

[Goonie]

My friend send me link to this interesting video: "What if 3D printing was 100x faster?"

http://www.ted.com/talks/joe_desimone_what_if_3d_printing_was_25x_faster#t-626886

[Volkodav]

There's a weekly magazine with bits to build your own 3d printer out now.

[GTX_Admin]

There's a weekly magazine with bits to build your own 3d printer out now.

That would be this one